IFR arrival and approach procedure[PDF]
The design of an approach procedure is, in general, dictated by the terrain surrounding the airfield, the type of operation contemplated and the aircraft to be accommodated.
Instrument approach procedures are classified as follows:
- Non-precision approach (NPA) procedure: An instrument approach procedure designed for 2D instrument approach operations Type A.
- Approach procedure with vertical guidance (APV): A performance-based navigation (PBN) instrument approach procedure designed for 3D instrument approach operations Type A.
- Precision approach (PA) procedure: An instrument approach procedure based on navigation systems (ILS, MLS, GLS and SBAS CAT I) designed for 3D instrument approach operations Type A or B.
There are two methods for executing instrument approach operations:
- a two-dimensional (2D) instrument approach operation, using lateral navigation guidance only;
- a three-dimensional (3D) instrument approach operation, using both lateral and vertical navigation guidance.
Instrument approach operations include an instrument phase and a visual phase:
- The instrument phase ends at the published MDA/H or DA/H unless a missed approach is initiated.
- The continued approach to landing from MDA/H or DA/H will be conducted using visual references.
Lateral and vertical navigation guidance refers to the guidance provided either by:
- a ground-based radio navigation aid
- computer-generated navigation data from ground-based, space-based, self-contained navigation aids or a combination of these.
Consult the document that describe the IFR precision approach and minima in order to have more information.
Categories of aircraft for approach procedures
Accordingly, categories of aircraft have been established. These categories provide a standardized basis for relating aircraft manoeuvrability to specific instrument approach procedures.
The table which describe the category list in function of Vat can be consulted in the article : Category of aircraft for approach procedures
For each individual approach procedure, an obstacle clearance altitude/height OCA/H is published on the instrument approach chart for each applicable category of aircraft.
- In a precision approach procedure, the lowest altitude (OCA) above the elevation of the relevant runway threshold at which a missed approach must be initiated.
- In a non-precision approach procedure, the lowest altitude (OCA) above the aerodrome elevation or the elevation of the relevant runway threshold, if the threshold elevation is more than 2m (7ft) below the aerodrome elevation (OCH) below which an aircraft cannot descend without infringing the appropriate obstacle clearance criteria
- In a visual (circling) procedure, the altitude (OCA) above the aerodrome elevation below which an aircraft cannot descend without infringing the appropriate obstacle clearance criteria
In general, minima are developed by adding the effect of a number of operational factors to OCA/H to produce:
- Decision altitude (DA) or decision height (DH) for precision approach
- Minimum descent altitude (MDA) or minimum descent height (MDH) for non-precision approach
Speed range for procedure calculation
The procedures and the tracks protection are constructed using a predefined speed range depending on the localization inside the approach tracks.
The speed ranges are described in the article : Category of aircraft for approach procedures
Segments of approach procedure
These approach segments begin and end at designated fixes or specified points where no fixes are available.
IAF = initial approach fix is a fix that marks the beginning of the initial segment and the end of the arrival segment, if applicable. In RNAV application, this fix is normally defined by a fly-by waypoint.
IF = intermediate fix is a fix that marks the end of an initial segment and the beginning of the intermediate segment. In RNAV application, this fix is normally defined by a fly-by waypoint.
FAF = final approach fix is a fix that marks the end of an intermediate segment and the beginning of the final approach segment for non-precision approach.
FAP = final approach point is a fix that marks the end of an intermediate segment and the beginning of the final approach segment for precision approach
MAPt = Missed approach point is a point in an instrument approach procedure at or before which the prescribed missed approach procedure must be initiated in order to ensure that the minimum obstacle clearance is not infringed.
DA = A specified altitude or height in a 3D instrument approach operation at which a missed approach must be initiated if the required visual reference to continue the approach has not been established.
MDA = A specified altitude or height in a 2D instrument approach operation or circling approach operation below which descent must not be made without the required visual reference.
MAHF = Missed approach holding fix is a fix used in RNAV application that marks the end of the missed approach segment and the centre point for the missed approach holding.
MSA = Minimum sector altitude is the lowest altitude which may be used which will provide a minimum clearance of 300m (1000ft) above all objects located in an area contained within a sector of a circle of 46km (25NM) radius centred on a radio aid to navigation.
- IFR Approach procedure - Arrival segment, IFR Approach procedure - Initial approach segment, IFR Approach procedure - Intermediate approach segment, IFR Approach procedure - Final approach segment, IFR Approach procedure - Missed approach segment
- IFR precision approach and minima,Category of aircraft for approach procedures
- ICAO Documentation 8168 - Aircraft Operations - Volume I - Flight Procedures - 6th Edition 2010 - Section 4
- VID 150259 - Creation
- VID 531824 - Wiki Integration
DATE OF SUBMISSION
- 01:00, 14 May 2021
- This documentation is copyrighted as part of the intellectual property of the International Virtual Aviation Organisation.
- The content of this documentation is intended for aviation simulation only and must not be used for real aviation operations.